Üdvözöljük itt: Pirometer.hu! - Hívjon +36 1 4057771
Automatikus égővezérlő egységek BCU 370
Automatikus égővezérlők beépített gyújtó transzformátorral, fém házban kényszerlevegős gázégők felügyeletére és vezérlésére, folyamatos üzemre, ionizációs vagy UV lángőrzésre az EN 676 -nak megfelelő berendezésekhez. Üzemállapot, paraméterek és lángjel megjelenítése. Diagnosztika és paraméter állítás optikai csatlakozóval. Kézi üzemeltetés égőbeállításhoz. Gáz- és levegőnyomás ellenőrzés valamint opcionális tömörségvizsgálat külső nyomáskapcsolókkal. Motoros levegő pillangószelep vezérléssel.
BCU 370...B1: Profibus DP kapcsolattal
Biztonsági idő gyújtáskor: 3 s, 5 s vagy 10 s
Biztonsági idő üzem közben: 1 s vagy 2 s
Működtető feszültség: 120 V AC vagy 230 V AC
BCU 370QI1FEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 120 V AC, 50/60 Hz
- Electronic ignition, single-pole
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 3 s
- 15 Flame stabilisation time 2, main burner tFS2: 2 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: off
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: DGmax. monitoring
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 2 s
- 25 Valve control: on
- 31 Bus control activation: off
- 32 Bus control limitation: Closed position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 30 s
- 19 Post-purge time tPN: 0 s
BCU 370QI1FEU0D3B1-3
Burner control unit, series 300
- T-product, FM and CSA approved
- Mains voltage: 120 V AC, 50/60 Hz
- Electronic ignition, single-pole
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 3 s
- 15 Flame stabilisation time 2, main burner tFS2: 2 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 2 s
- 27 V2 during burner operation: off
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 0 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Ignition position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 10 s
- 19 Post-purge time tPN: 0 s
BCU 370QI1FEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 120 V AC, 50/60 Hz
- Electronic ignition, single-pole
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 3 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 3 s
- 15 Flame stabilisation time 2, main burner tFS2: 2 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: off
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 0 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Ignition position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 30 s
- 19 Post-purge time tPN: 0 s
BCU 370QI1FEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 120 V AC, 50/60 Hz
- Electronic ignition, single-pole
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 3 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 3 s
- 15 Flame stabilisation time 2, main burner tFS2: 2 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: off
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 0 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Low position
- 06 Pre-purge on each start-up: off
- 28 Quick start-up starts in Ignition position
- 18 Pre-purge time tPV: 30 s
- 19 Post-purge time tPN: 15 s
BCU 370QI1FEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 120 V AC, 50/60 Hz
- Electronic ignition, single-pole
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 3 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 3 s
- 15 Flame stabilisation time 2, main burner tFS2: 2 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: off
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 0 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Low position
- 06 Pre-purge on each start-up: off
- 28 Quick start-up starts in Ignition position
- 18 Pre-purge time tPV: 10 s
- 19 Post-purge time tPN: 15 s
BCU 370QI1FEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 120 V AC, 50/60 Hz
- Electronic ignition, single-pole
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 3 s
- 15 Flame stabilisation time 2, main burner tFS2: 2 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: off
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 0 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Ignition position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 30 s
- 19 Post-purge time tPN: 0 s
BCU 370QI1FEU0D3B1-3
Burner control unit, series 300
- T-product, FM and CSA approved
- Mains voltage: 120 V AC, 50/60 Hz
- Electronic ignition, single-pole
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 3 s
- 15 Flame stabilisation time 2, main burner tFS2: 2 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: off
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 2 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Ignition position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 30 s
- 19 Post-purge time tPN: 0 s
BCU 370QI1FEU0D3B1-3
Burner control unit, series 300
- T-product, FM and CSA approved
- Mains voltage: 120 V AC, 50/60 Hz
- Electronic ignition, single-pole
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 3 s
- 15 Flame stabilisation time 2, main burner tFS2: 2 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 2 s
- 27 V2 during burner operation: off
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: off
- 05 Air monitoring during operation: off
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 5 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Ignition position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 30 s
- 19 Post-purge time tPN: 0 s
BCU 370QI3FEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 120 V AC, 50/60 Hz
- Electronic ignition, double-pole with neutral conductor
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 3 s
- 15 Flame stabilisation time 2, main burner tFS2: 2 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 2 s
- 27 V2 during burner operation: off
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 0 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Closed position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 30 s
- 19 Post-purge time tPN: 0 s
BCU 370WI1FEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 230 V AC, 50/60 Hz
- Electronic ignition, single-pole
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 3 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 3 s
- 15 Flame stabilisation time 2, main burner tFS2: 2 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: on
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: inactive
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 2 s
- 25 Valve control: on
- 31 Bus control activation: off
- 32 Bus control limitation: Low position
- 06 Pre-purge on each start-up: off
- 28 Quick start-up starts in Ignition position
- 18 Pre-purge time tPV: 10 s
- 19 Post-purge time tPN: 2 s
BCU 370WI1FEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 230 V AC, 50/60 Hz
- Electronic ignition, single-pole
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 0 s
- 15 Flame stabilisation time 2, main burner tFS2: 0 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: on
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 30 s
- 20 Fan run up time tGV: 2 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Ignition position
- 06 Pre-purge on each start-up: off
- 28 Quick start-up starts in Ignition position
- 18 Pre-purge time tPV: 30 s
- 19 Post-purge time tPN: 30 s
BCU 370WI1FEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 230 V AC, 50/60 Hz
- Electronic ignition, single-pole
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 0 s
- 15 Flame stabilisation time 2, main burner tFS2: 0 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: on
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 30 s
- 20 Fan run up time tGV: 2 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Low position
- 06 Pre-purge on each start-up: off
- 28 Quick start-up starts in Ignition position
- 18 Pre-purge time tPV: 30 s
- 19 Post-purge time tPN: 30 s
BCU 370WI1FEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 230 V AC, 50/60 Hz
- Electronic ignition, single-pole
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 3 s
- 15 Flame stabilisation time 2, main burner tFS2: 2 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: off
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 0 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Low position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 30 s
- 19 Post-purge time tPN: 0 s
BCU 370WI1FEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 230 V AC, 50/60 Hz
- Electronic ignition, single-pole
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 0 s
- 15 Flame stabilisation time 2, main burner tFS2: 0 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: on
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 0 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Ignition position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 30 s
- 19 Post-purge time tPN: 0 s
BCU 370WI1FEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 230 V AC, 50/60 Hz
- Electronic ignition, single-pole
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 2
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 3 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 0 s
- 15 Flame stabilisation time 2, main burner tFS2: 0 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: off
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: on
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 20 s
- 20 Fan run up time tGV: 2 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Low position
- 06 Pre-purge on each start-up: off
- 28 Quick start-up starts in Ignition position
- 18 Pre-purge time tPV: 20 s
- 19 Post-purge time tPN: 20 s
BCU 370WI1FEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 230 V AC, 50/60 Hz
- Electronic ignition, single-pole
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 3 s
- 15 Flame stabilisation time 2, main burner tFS2: 2 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: off
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 0 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Ignition position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 30 s
- 19 Post-purge time tPN: 0 s
BCU 370WI1FEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 230 V AC, 50/60 Hz
- Electronic ignition, single-pole
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 3 s
- 15 Flame stabilisation time 2, main burner tFS2: 2 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: off
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 0 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Closed position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 30 s
- 19 Post-purge time tPN: 0 s
BCU 370WI1FEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 230 V AC, 50/60 Hz
- Electronic ignition, single-pole
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 3 s
- 15 Flame stabilisation time 2, main burner tFS2: 2 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: off
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: DGmax. monitoring
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 2 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Ignition position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 30 s
- 19 Post-purge time tPN: 0 s
BCU 370WI1FEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 230 V AC, 50/60 Hz
- Electronic ignition, single-pole
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 0 s
- 15 Flame stabilisation time 2, main burner tFS2: 0 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: on
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: unlimited
- 30 User-defined password
- 04 Air monitoring during pre-purge: off
- 05 Air monitoring during operation: off
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 0 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Low position
- 06 Pre-purge on each start-up: off
- 28 Quick start-up starts in Closed position
- 18 Pre-purge time tPV: 30 s
- 19 Post-purge time tPN: 10 s
BCU 370WI1FEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 230 V AC, 50/60 Hz
- Electronic ignition, single-pole
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 2
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 3 s
- 15 Flame stabilisation time 2, main burner tFS2: 2 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: off
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: unlimited
- 30 User-defined password
- 04 Air monitoring during pre-purge: off
- 05 Air monitoring during operation: off
- 23 Min. gas pressure monitoring: off
- 24 Digital input function: inactive
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 0 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Ignition position
- 06 Pre-purge on each start-up: off
- 28 Quick start-up starts in Ignition position
- 18 Pre-purge time tPV: 10 s
- 19 Post-purge time tPN: 10 s
BCU 370WI1FEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 230 V AC, 50/60 Hz
- Electronic ignition, single-pole
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 3 s
- 15 Flame stabilisation time 2, main burner tFS2: 2 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: off
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: DGmax. monitoring
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 2 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Ignition position
- 06 Pre-purge on each start-up: off
- 28 Quick start-up starts in Ignition position
- 18 Pre-purge time tPV: 30 s
- 19 Post-purge time tPN: 0 s
BCU 370WI1FEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 230 V AC, 50/60 Hz
- Electronic ignition, single-pole
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 0 s
- 15 Flame stabilisation time 2, main burner tFS2: 0 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: off
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 2 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Ignition position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 120 s
- 19 Post-purge time tPN: 120 s
BCU 370WI1FEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 230 V AC, 50/60 Hz
- Electronic ignition, single-pole
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 3 s
- 15 Flame stabilisation time 2, main burner tFS2: 2 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: off
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 0 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Low position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 30 s
- 19 Post-purge time tPN: 0 s
BCU 370WI1FEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 230 V AC, 50/60 Hz
- Electronic ignition, single-pole
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 3 s
- 15 Flame stabilisation time 2, main burner tFS2: 2 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: off
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: DGmax. monitoring
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 0 s
- 25 Valve control: on
- 31 Bus control activation: off
- 32 Bus control limitation: Closed position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 30 s
- 19 Post-purge time tPN: 0 s
BCU 370WI1FEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 230 V AC, 50/60 Hz
- Electronic ignition, single-pole
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 3 s
- 15 Flame stabilisation time 2, main burner tFS2: 2 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: off
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: DGmax. monitoring
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 2 s
- 25 Valve control: on
- 31 Bus control activation: off
- 32 Bus control limitation: Closed position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 30 s
- 19 Post-purge time tPN: 0 s
BCU 370WI1FEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 230 V AC, 50/60 Hz
- Electronic ignition, single-pole
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 3 s
- 15 Flame stabilisation time 2, main burner tFS2: 2 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: off
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 0 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Ignition position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 30 s
- 19 Post-purge time tPN: 0 s
BCU 370WI1FEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 230 V AC, 50/60 Hz
- Electronic ignition, single-pole
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 3 s
- 15 Flame stabilisation time 2, main burner tFS2: 2 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: off
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 2 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Ignition position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 30 s
- 19 Post-purge time tPN: 0 s
BCU 370WI1FEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 230 V AC, 50/60 Hz
- Electronic ignition, single-pole
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 3 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 3 s
- 15 Flame stabilisation time 2, main burner tFS2: 2 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: on
- 08 Behaviour after flame failure during operation: restart
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: DGmax. monitoring
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 2 s
- 25 Valve control: off
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 10 s
- 19 Post-purge time tPN: 0 s
BCU 370WI1FEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 230 V AC, 50/60 Hz
- Electronic ignition, single-pole
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 3 s
- 15 Flame stabilisation time 2, main burner tFS2: 2 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: off
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 0 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Ignition position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 10 s
- 19 Post-purge time tPN: 0 s
BCU 370WI1FEU1D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 230 V AC, 50/60 Hz
- Electronic ignition, single-pole
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: UV control (continuous operation with UVD)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 3 s
- 15 Flame stabilisation time 2, main burner tFS2: 2 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: off
- 08 Behaviour after flame failure during operation: fault lock-out
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: DGmax. monitoring
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 2 s
- 25 Valve control: on
- 31 Bus control activation: off
- 32 Bus control limitation: Closed position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 30 s
- 19 Post-purge time tPN: 0 s
BCU 370WI2FEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 230 V AC, 50/60 Hz
- Electronic ignition, double-pole
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 4
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 3 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 3 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 0 s
- 15 Flame stabilisation time 2, main burner tFS2: 0 s
- 29 Controller enable signal delay time tRF: 30 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: on
- 08 Behaviour after flame failure during operation: restart
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 5 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Ignition position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 20 s
- 19 Post-purge time tPN: 10 s
BCU 370WI2FEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 230 V AC, 50/60 Hz
- Electronic ignition, double-pole
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 3 s
- 15 Flame stabilisation time 2, main burner tFS2: 2 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: off
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 0 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Closed position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 30 s
- 19 Post-purge time tPN: 0 s
BCU 370WI2FEU1D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 230 V AC, 50/60 Hz
- Electronic ignition, double-pole
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: UV control (continuous operation with UVD)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 0 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 3 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 5 s
- 14 Safety time 2, main burner start-up tSA2: 3 s
- 15 Flame stabilisation time 2, main burner tFS2: 10 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: off
- 08 Behaviour after flame failure during operation: fault lock-out
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 0 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Ignition position
- 06 Pre-purge on each start-up: off
- 28 Quick start-up starts in Closed position
- 18 Pre-purge time tPV: 10 s
- 19 Post-purge time tPN: 10 s
BCU 370QFEU0D3B1-3
Burner control unit, series 300
- T-product, FM and CSA approved
- Mains voltage: 120 V AC, 50/60 Hz
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 3 s
- 15 Flame stabilisation time 2, main burner tFS2: 2 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: off
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: DGmax. monitoring
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 2 s
- 25 Valve control: on
- 31 Bus control activation: off
- 32 Bus control limitation: Closed position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 30 s
- 19 Post-purge time tPN: 0 s
BCU 370QFEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 120 V AC, 50/60 Hz
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 0 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 0 s
- 14 Safety time 2, main burner start-up tSA2: 0 s
- 15 Flame stabilisation time 2, main burner tFS2: 0 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 2 s
- 27 V2 during burner operation: on
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 5 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Low position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 10 s
- 19 Post-purge time tPN: 0 s
BCU 370QFEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 120 V AC, 50/60 Hz
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 0 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 0 s
- 15 Flame stabilisation time 2, main burner tFS2: 0 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: off
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: off
- 23 Min. gas pressure monitoring: off
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 0 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Closed position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 15 s
- 19 Post-purge time tPN: 0 s
BCU 370QFEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 120 V AC, 50/60 Hz
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 3 s
- 15 Flame stabilisation time 2, main burner tFS2: 2 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: off
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: DGmax. monitoring
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 2 s
- 25 Valve control: on
- 31 Bus control activation: off
- 32 Bus control limitation: Closed position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 30 s
- 19 Post-purge time tPN: 0 s
BCU 370QFEU0D3B1-3
Burner control unit, series 300
- T-product, FM and CSA approved
- Mains voltage: 120 V AC, 50/60 Hz
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 0 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 2 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 0 s
- 14 Safety time 2, main burner start-up tSA2: 5 s
- 15 Flame stabilisation time 2, main burner tFS2: 0 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: on
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 3 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: unlimited
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: off
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 3 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Ignition position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 30 s
- 19 Post-purge time tPN: 0 s
BCU 370QFEU0D3B1-3
Burner control unit, series 300
- T-product, FM and CSA approved
- Mains voltage: 120 V AC, 50/60 Hz
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 3 s
- 15 Flame stabilisation time 2, main burner tFS2: 2 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: off
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 2 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Ignition position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 30 s
- 19 Post-purge time tPN: 0 s
BCU 370QFEU0D3B1-3
Burner control unit, series 300
- T-product, FM, CSA and UL approved
- Mains voltage: 120 V AC, 50/60 Hz
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 0 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 0 s
- 14 Safety time 2, main burner start-up tSA2: 0 s
- 15 Flame stabilisation time 2, main burner tFS2: 0 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 2 s
- 27 V2 during burner operation: on
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 5 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Low position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 10 s
- 19 Post-purge time tPN: 0 s
BCU 370QFEU0D3B1-3
Burner control unit, series 300
- T-product, FM and CSA approved
- Mains voltage: 120 V AC, 50/60 Hz
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 0 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 2 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 0 s
- 14 Safety time 2, main burner start-up tSA2: 5 s
- 15 Flame stabilisation time 2, main burner tFS2: 0 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: on
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 3 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: unlimited
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: off
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 3 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Ignition position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 30 s
- 19 Post-purge time tPN: 0 s
BCU 370QFEU0D3B1-3
Burner control unit, series 300
- T-product, FM, CSA and UL approved
- Mains voltage: 120 V AC, 50/60 Hz
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 3 s
- 15 Flame stabilisation time 2, main burner tFS2: 2 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: off
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 2 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Ignition position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 30 s
- 19 Post-purge time tPN: 0 s
BCU 370QFEU0D3B1-3
Burner control unit, series 300
- T-product, FM, CSA and UL approved
- Mains voltage: 120 V AC, 50/60 Hz
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 3 s
- 15 Flame stabilisation time 2, main burner tFS2: 2 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 2 s
- 27 V2 during burner operation: off
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: off
- 05 Air monitoring during operation: off
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 5 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Ignition position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 30 s
- 19 Post-purge time tPN: 0 s
BCU 370QFEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 120 V AC, 50/60 Hz
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 3 s
- 15 Flame stabilisation time 2, main burner tFS2: 2 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: off
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 2 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Ignition position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 30 s
- 19 Post-purge time tPN: 0 s
BCU 370QFEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 120 V AC, 50/60 Hz
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 3 s
- 15 Flame stabilisation time 2, main burner tFS2: 2 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: off
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: DGmax. monitoring
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 0 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Closed position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 30 s
- 19 Post-purge time tPN: 0 s
BCU 370WFEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 230 V AC, 50/60 Hz
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 3 s
- 15 Flame stabilisation time 2, main burner tFS2: 2 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: off
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: on
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: DGmax. monitoring
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 2 s
- 25 Valve control: on
- 31 Bus control activation: off
- 32 Bus control limitation: Closed position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 30 s
- 19 Post-purge time tPN: 0 s
BCU 370WFEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 230 V AC, 50/60 Hz
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 5 s
- 07 Burner start-up attempts: 2
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 3 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 0 s
- 15 Flame stabilisation time 2, main burner tFS2: 0 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: on
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 2 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Low position
- 06 Pre-purge on each start-up: off
- 28 Quick start-up starts in Closed position
- 18 Pre-purge time tPV: 10 s
- 19 Post-purge time tPN: 10 s
BCU 370WFEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 230 V AC, 50/60 Hz
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 3 s
- 15 Flame stabilisation time 2, main burner tFS2: 2 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: off
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: DGmax. monitoring
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 2 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Ignition position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 30 s
- 19 Post-purge time tPN: 0 s
BCU 370WFEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 230 V AC, 50/60 Hz
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 0 s
- 15 Flame stabilisation time 2, main burner tFS2: 0 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: on
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 30 s
- 20 Fan run up time tGV: 2 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Ignition position
- 06 Pre-purge on each start-up: off
- 28 Quick start-up starts in Ignition position
- 18 Pre-purge time tPV: 30 s
- 19 Post-purge time tPN: 30 s
BCU 370WFEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 230 V AC, 50/60 Hz
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 3 s
- 15 Flame stabilisation time 2, main burner tFS2: 2 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: on
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: on
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 0 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Ignition position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 60 s
- 19 Post-purge time tPN: 0 s
BCU 370WFEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 230 V AC, 50/60 Hz
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 2
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 3 s
- 15 Flame stabilisation time 2, main burner tFS2: 2 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: on
- 08 Behaviour after flame failure during operation: restart
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 10 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Ignition position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 10 s
- 19 Post-purge time tPN: 0 s
BCU 370WFEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 230 V AC, 50/60 Hz
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 3 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 0 s
- 15 Flame stabilisation time 2, main burner tFS2: 0 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: on
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 2 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Ignition position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 30 s
- 19 Post-purge time tPN: 0 s
BCU 370WFEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 230 V AC, 50/60 Hz
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 3 s
- 15 Flame stabilisation time 2, main burner tFS2: 2 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: off
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: DGmax. monitoring
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 2 s
- 25 Valve control: on
- 31 Bus control activation: off
- 32 Bus control limitation: Closed position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 30 s
- 19 Post-purge time tPN: 0 s
BCU 370WFEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 230 V AC, 50/60 Hz
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 3 s
- 15 Flame stabilisation time 2, main burner tFS2: 2 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: on
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: DGmax. monitoring
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 2 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Ignition position
- 06 Pre-purge on each start-up: off
- 28 Quick start-up starts in Ignition position
- 18 Pre-purge time tPV: 30 s
- 19 Post-purge time tPN: 0 s
BCU 370WFEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 230 V AC, 50/60 Hz
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 3 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 0 s
- 15 Flame stabilisation time 2, main burner tFS2: 0 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: on
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 2 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Ignition position
- 06 Pre-purge on each start-up: off
- 28 Quick start-up starts in Ignition position
- 18 Pre-purge time tPV: 250 s
- 19 Post-purge time tPN: 10 s
BCU 370WFEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 230 V AC, 50/60 Hz
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 2
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 3 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 0 s
- 15 Flame stabilisation time 2, main burner tFS2: 0 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: on
- 08 Behaviour after flame failure during operation: restart
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 0 s
- 25 Valve control: on
- 31 Bus control activation: off
- 32 Bus control limitation: Closed position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 10 s
- 19 Post-purge time tPN: 0 s
BCU 370WFEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 230 V AC, 50/60 Hz
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 3 s
- 15 Flame stabilisation time 2, main burner tFS2: 2 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: off
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 0 s
- 25 Valve control: on
- 31 Bus control activation: on
- 32 Bus control limitation: Ignition position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 30 s
- 19 Post-purge time tPN: 0 s
BCU 370WFEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 230 V AC, 50/60 Hz
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 0 s
- 15 Flame stabilisation time 2, main burner tFS2: 0 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: off
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: off
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 0 s
- 25 Valve control: on
- 31 Bus control activation: off
- 32 Bus control limitation: Ignition position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 30 s
- 19 Post-purge time tPN: 0 s
BCU 370WFEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 230 V AC, 50/60 Hz
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 5 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 2 s
- 14 Safety time 2, main burner start-up tSA2: 3 s
- 15 Flame stabilisation time 2, main burner tFS2: 2 s
- 29 Controller enable signal delay time tRF: 10 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: off
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: integrated tightness control
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 2 s
- 25 Valve control: on
- 31 Bus control activation: off
- 32 Bus control limitation: Closed position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 30 s
- 19 Post-purge time tPN: 0 s
BCU 370WFEU0D3B1-3
Burner control unit, series 300
- European market, EC type tested and certified
- Mains voltage: 230 V AC, 50/60 Hz
- Fan control: 3 A relay
- Valve control: three-point step
- Flame control: ionisation control (continuous or intermittent operation) or UV control (intermittent operation with UVS)
- Digital input function: integrated tightness control
- Fieldbus interface: PROFIBUS-DP
- Bus control: three-point step
- With bottom section
- 11 Minimum burner pause time tBP: 0 s
- 07 Burner start-up attempts: 1
- 22 Switch-on delay time tE: 0 s
- 21 Pre-ignition time tVZ: 1 s
- 12 Safety time 1, burner/pilot burner start-up tSA1: 3 s
- 13 Flame stabilisation time 1, burner/pilot tFS1: 5 s
- 14 Safety time 2, main burner start-up tSA2: 0 s
- 15 Flame stabilisation time 2, main burner tFS2: 0 s
- 29 Controller enable signal delay time tRF: 0 s
- 10 Minimum combustion time tB: 0 s
- 09 Safety time during operation tSB: 1 s
- 27 V2 during burner operation: on
- 08 Behaviour after flame failure during operation: fault lock-out
- 02 Burner switch-off threshold: 1 mikro A
- 17 UVS check: off
- 16 Operating time in manual mode: limited to 5 minutes
- 30 User-defined password
- 04 Air monitoring during pre-purge: on
- 05 Air monitoring during operation: on
- 23 Min. gas pressure monitoring: on
- 24 Digital input function: DGmax. monitoring
- 26 TC test period tP: 10 s
- 20 Fan run up time tGV: 0 s
- 25 Valve control: on
- 31 Bus control activation: off
- 32 Bus control limitation: Closed position
- 06 Pre-purge on each start-up: on
- 18 Pre-purge time tPV: 240 s
- 19 Post-purge time tPN: 0 s