Automatikus égővezérlő egységek BCU 400
Automatikus égővezérlők beépített gyújtó transzformátorral, fém házban gázégők felügyeletére és vezérlésére, folyamatos üzemre, ionizációs vagy UV lángőrzésre. Üzemállapot, paraméterek és lángjel megjelenítése. Diagnosztika és paraméter állítás optikai csatlakozóval. Kézi üzemeltetés égőbeállításhoz. Tanusítással SIL 3 és PL e rendszerekhez.
BCU 440: közvetlen gyújtású, ionizációs lángőrzésű égőkhöz max. 350 kW -ig
BCU 460: közvetlen gyújtású égőkhöz, opcionális levegő szelep vezérléssel
BCU 465: további levegő szelep vezérlési lehetőségekkel, elsősorban sugárzócsöves égőkhöz
BCU 480: gyújtóégővel gyújtott égőkhöz
BCU 4...B1: Profibus DP kapcsolattal
Biztonsági idő gyújtáskor: 3 s, 5 s vagy 10 s
Biztonsági idő üzem közben: 1 s vagy 2 s
Működtető feszültség: 115 V AC vagy 230 V AC
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 3 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with intermittent operation with UVS
- With circuit board for signal distribution
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Fault lock-out after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for double-electrode operation
- Time between two start-ups: 10 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 3 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with continuous operation with ionisation/UVD
- With circuit board for signal distribution
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Fault lock-out after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for double-electrode operation
- Time between two start-ups: 10 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 5 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with intermittent operation with UVS
- With circuit board for signal distribution
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Restart after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 5 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for double-electrode operation
- Time between two start-ups: 15 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 5 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with intermittent operation with UVS
- With circuit board for signal distribution
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Fault lock-out after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for double-electrode operation
- Time between two start-ups: 15 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 5 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with continuous operation with ionisation/UVD
- With circuit board for signal distribution
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Fault lock-out after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for double-electrode operation
- Time between two start-ups: 15 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 5 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with continuous operation with ionisation/UVD
- 2 start-up attempts, pilot burner
- 1 start-up attempt, main burner
- With circuit board for signal distribution
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Restart after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for single-electrode operation
- Time between two start-ups: 15 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 5 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with continuous operation with ionisation/UVD
- 2 start-up attempts, pilot burner
- 2 start-up attempts, main burner
- With circuit board for signal distribution
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Fault lock-out after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for single-electrode operation
- Time between two start-ups: 15 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 5 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with continuous operation with ionisation/UVD
- 2 start-up attempts, pilot burner
- 2 start-up attempts, main burner
- With circuit board for signal distribution
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Fault lock-out after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for double-electrode operation
- Time between two start-ups: 15 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 5 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with continuous operation with ionisation/UVD
- 3 start-up attempts, pilot burner
- 1 start-up attempt, main burner
- With circuit board for signal distribution
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Fault lock-out after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for double-electrode operation
- Time between two start-ups: 15 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 5 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with continuous operation with ionisation/UVD
- 3 start-up attempts, pilot burner
- 2 start-up attempts, main burner
- With circuit board for signal distribution
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 5 mikro A
- 12 Restart after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for double-electrode operation
- Time between two start-ups: 15 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 5 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 5-15/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with continuous operation with ionisation/UVD
- 2 start-up attempts, pilot burner
- 2 start-up attempts, main burner
- With circuit board for signal distribution
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Fault lock-out after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for double-electrode operation
- Time between two start-ups: 10 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 5 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 5-15/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with continuous operation with ionisation/UVD
- 2 start-up attempts, pilot burner
- 2 start-up attempts, main burner
- With circuit board for signal distribution
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Fault lock-out after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for single-electrode operation
- Time between two start-ups: 10 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 5 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 5-15/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with continuous operation with ionisation/UVD
- 2 start-up attempts, pilot burner
- 2 start-up attempts, main burner
- With circuit board for signal distribution
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- Voltage for valves and ignition transformer via L1
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Fault lock-out after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for single-electrode operation
- Time between two start-ups: 10 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 3 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 115 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with intermittent operation with UVS
- 2 start-up attempts, pilot burner
- 1 start-up attempt, main burner
- PROFIBUS-DP interface
- Integrated standard PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Fault lock-out after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for double-electrode operation
- Time between two start-ups: 10 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 3 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-20/33
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with intermittent operation with UVS
- 2 start-up attempts, pilot burner
- 2 start-up attempts, main burner
- PROFIBUS-DP interface
- Integrated standard PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 4 mikro A
- 05 Main burner switch-off threshold: 4 mikro A
- 12 Restart after pilot burner failure in operation
- 13 Restart after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: 10 s
- 21 Minimum burner pause time tBP: 10 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve opens with V1
- 31 Air valve can be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for double-electrode operation
- Time between two start-ups: 10 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 5 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with intermittent operation with UVS
- 2 start-up attempts, pilot burner
- 1 start-up attempt, main burner
- PROFIBUS-DP interface
- Integrated standard PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Fault lock-out after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve opens with V2
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for single-electrode operation
- Time between two start-ups: 15 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 5 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with intermittent operation with UVS
- 2 start-up attempts, pilot burner
- 1 start-up attempt, main burner
- PROFIBUS-DP interface
- Integrated standard PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Fault lock-out after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for double-electrode operation
- Time between two start-ups: 15 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 5 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with intermittent operation with UVS
- 2 start-up attempts, pilot burner
- 1 start-up attempt, main burner
- PROFIBUS-DP interface
- Integrated standard PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Restart after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve opens with V2
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for single-electrode operation
- Time between two start-ups: 15 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 5 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with continuous operation with ionisation/UVD
- 2 start-up attempts, pilot burner
- 1 start-up attempt, main burner
- PROFIBUS-DP interface
- Integrated standard PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Restart after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for double-electrode operation
- Time between two start-ups: 15 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 5 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-20/33
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with continuous operation with ionisation/UVD
- 2 start-up attempts, pilot burner
- 1 start-up attempt, main burner
- PROFIBUS-DP interface
- Integrated standard PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Fault lock-out after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve opens with V2
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: closed
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for single-electrode operation
- Time between two start-ups: 20 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 3 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 5-15/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with intermittent operation with UVS
- 2 start-up attempts, pilot burner
- 2 start-up attempts, main burner
- PROFIBUS-DP interface
- Integrated standard PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 4 mikro A
- 05 Main burner switch-off threshold: 4 mikro A
- 12 Restart after pilot burner failure in operation
- 13 Restart after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: 10 s
- 21 Minimum burner pause time tBP: 10 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve opens with V1
- 31 Air valve can be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for single-electrode operation
- Time between two start-ups: 10 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 3 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 5-15/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with intermittent operation with UVS
- 2 start-up attempts, pilot burner
- 2 start-up attempts, main burner
- PROFIBUS-DP interface
- Integrated standard PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 4 mikro A
- 05 Main burner switch-off threshold: 4 mikro A
- 12 Restart after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: 10 s
- 21 Minimum burner pause time tBP: 10 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for single-electrode operation
- Time between two start-ups: 10 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 5 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 5-15/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with intermittent operation with UVS
- 2 start-up attempts, pilot burner
- 2 start-up attempts, main burner
- PROFIBUS-DP interface
- Integrated standard PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 4 mikro A
- 05 Main burner switch-off threshold: 4 mikro A
- 12 Restart after pilot burner failure in operation
- 13 Restart after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: 10 s
- 21 Minimum burner pause time tBP: 10 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve opens with V1
- 31 Air valve can be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for single-electrode operation
- Time between two start-ups: 10 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 5 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 5-15/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with continuous operation with ionisation/UVD
- 2 start-up attempts, pilot burner
- 1 start-up attempt, main burner
- PROFIBUS-DP interface
- Integrated standard PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Restart after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for single-electrode operation
- Time between two start-ups: 10 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 10 s
- 2nd safety time on start-up (main burner) tSA2: 10 s
- Safety time in operation tSB: 2 s
- Air valve control
- Mains voltage: 115 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- High temperature operation: with intermittent operation with UVS
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Fault lock-out after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 1 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for double-electrode operation
- Time between two start-ups: 30 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 10 s
- 2nd safety time on start-up (main burner) tSA2: 10 s
- Safety time in operation tSB: 2 s
- Air valve control
- Mains voltage: 115 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- High temperature operation: with continuous operation with ionisation/UVD
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Fault lock-out after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for double-electrode operation
- Time between two start-ups: 30 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 10 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with intermittent operation with UVS
- 2 start-up attempts, pilot burner
- 1 start-up attempt, main burner
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Fault lock-out after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve opens with V2
- 31 Air valve can be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for single-electrode operation
- Time between two start-ups: 30 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 10 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with continuous operation with ionisation/UVD
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Fault lock-out after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: closed
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for single-electrode operation
- Time between two start-ups: 30 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 10 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with continuous operation with ionisation/UVD
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Fault lock-out after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Pilot burner is switched off
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: closed
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for single-electrode operation
- Time between two start-ups: 30 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 10 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-20/33
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with intermittent operation with UVS
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Fault lock-out after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for double-electrode operation
- Time between two start-ups: 30 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 10 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-20/33
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with intermittent operation with UVS
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 3 mikro A
- 12 Fault lock-out after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for double-electrode operation
- Time between two start-ups: 30 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 10 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 2 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with intermittent operation with UVS
- 3 start-up attempts, pilot burner
- 3 start-up attempts, main burner
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Fault lock-out after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for single-electrode operation
- Time between two start-ups: 30 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 10 s
- 2nd safety time on start-up (main burner) tSA2: 5 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 115 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with intermittent operation with UVS
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Restart after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for single-electrode operation
- Time between two start-ups: 30 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 10 s
- 2nd safety time on start-up (main burner) tSA2: 5 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 115 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with intermittent operation with UVS
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Fault lock-out after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Pilot burner is switched off
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 35 UVS check (1 x in 24 hours)
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for single-electrode operation
- Time between two start-ups: 30 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 10 s
- 2nd safety time on start-up (main burner) tSA2: 5 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with intermittent operation with UVS
- 2 start-up attempts, pilot burner
- 1 start-up attempt, main burner
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Restart after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve opens with V2
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for double-electrode operation
- Time between two start-ups: 30 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 10 s
- 2nd safety time on start-up (main burner) tSA2: 5 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with continuous operation with ionisation/UVD
- 2 start-up attempts, pilot burner
- 2 start-up attempts, main burner
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Fault lock-out after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for single-electrode operation
- Time between two start-ups: 30 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 3 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 115 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with intermittent operation with UVS
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Fault lock-out after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for double-electrode operation
- Time between two start-ups: 10 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 3 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with continuous operation with ionisation/UVD
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Fault lock-out after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for single-electrode operation
- Time between two start-ups: 10 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 5 s
- 2nd safety time on start-up (main burner) tSA2: 10 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with intermittent operation with UVS
- 2 start-up attempts, pilot burner
- 2 start-up attempts, main burner
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 4 mikro A
- 12 Restart after pilot burner failure in operation
- 13 Restart after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 10 s
- 25 Main burner flame proving period tFS2: 10 s
- 30 Air valve can be controlled externally
- 31 Air valve can be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for double-electrode operation
- Time between two start-ups: 15 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 5 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 115 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with intermittent operation with UVS
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Fault lock-out after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Pilot burner is switched off
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve opens with V1
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for double-electrode operation
- Time between two start-ups: 15 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 5 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 115 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with intermittent operation with UVS
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Restart after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve opens with V2
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for single-electrode operation
- Time between two start-ups: 15 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 5 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 115 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with intermittent operation with UVS
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Fault lock-out after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for double-electrode operation
- Time between two start-ups: 15 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 5 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 115 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with intermittent operation with UVS
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Fault lock-out after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve opens with V2
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for single-electrode operation
- Time between two start-ups: 15 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 5 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 115 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with intermittent operation with UVS
- 3 start-up attempts, pilot burner
- 1 start-up attempt, main burner
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Restart after pilot burner failure in operation
- 13 Restart after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for double-electrode operation
- Time between two start-ups: 15 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 5 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 115 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with continuous operation with ionisation/UVD
- 2 start-up attempts, pilot burner
- 1 start-up attempt, main burner
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Fault lock-out after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: 5 s
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for double-electrode operation
- Time between two start-ups: 15 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 5 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with intermittent operation with UVS
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Restart after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve opens with V1
- 31 Air valve can be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for single-electrode operation
- Time between two start-ups: 15 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 5 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with intermittent operation with UVS
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 7 mikro A
- 12 Fault lock-out after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 3 s
- 25 Main burner flame proving period tFS2: 3 s
- 30 Air valve can be controlled externally
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for single-electrode operation
- Time between two start-ups: 15 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 5 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with intermittent operation with UVS
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Fault lock-out after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: 5 s
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for double-electrode operation
- Time between two start-ups: 15 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 5 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with intermittent operation with UVS
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Restart after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve opens with V2
- 31 Air valve can be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for single-electrode operation
- Time between two start-ups: 15 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 5 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with intermittent operation with UVS
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Fault lock-out after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for double-electrode operation
- Time between two start-ups: 15 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 5 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with intermittent operation with UVS
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Restart after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for double-electrode operation
- Time between two start-ups: 15 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 5 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with intermittent operation with UVS
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Fault lock-out after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: closed
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for single-electrode operation
- Time between two start-ups: 15 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 5 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with intermittent operation with UVS
- 2 start-up attempts, pilot burner
- 1 start-up attempt, main burner
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Fault lock-out after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: 5 s
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for double-electrode operation
- Time between two start-ups: 15 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 5 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with intermittent operation with UVS
- 2 start-up attempts, pilot burner
- 1 start-up attempt, main burner
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 4 mikro A
- 12 Restart after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve opens with V2
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for single-electrode operation
- Time between two start-ups: 15 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 5 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with intermittent operation with UVS
- 2 start-up attempts, pilot burner
- 2 start-up attempts, main burner
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Restart after pilot burner failure in operation
- 13 Restart after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: 5 s
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for single-electrode operation
- Time between two start-ups: 15 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 5 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with intermittent operation with UVS
- 3 start-up attempts, pilot burner
- 1 start-up attempt, main burner
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Fault lock-out after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 35 UVS check (1 x in 24 hours)
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for double-electrode operation
- Time between two start-ups: 15 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 5 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with intermittent operation with UVS
- 3 start-up attempts, pilot burner
- 1 start-up attempt, main burner
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 1 mikro A
- 12 Fault lock-out after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 3 s
- 25 Main burner flame proving period tFS2: 3 s
- 30 Air valve can be controlled externally
- 31 Air valve can be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for single-electrode operation
- Time between two start-ups: 15 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 5 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with intermittent operation with UVS
- 3 start-up attempts, pilot burner
- 1 start-up attempt, main burner
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 4 mikro A
- 05 Main burner switch-off threshold: 4 mikro A
- 12 Fault lock-out after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 5 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 35 UVS check (1 x in 24 hours)
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for single-electrode operation
- Time between two start-ups: 15 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 5 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with intermittent operation with UVS
- 3 start-up attempts, pilot burner
- 1 start-up attempt, main burner
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 4 mikro A
- 05 Main burner switch-off threshold: 4 mikro A
- 12 Restart after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 5 s
- 23 Burener/pilot burner flame proving period tFS1: 0 s
- 25 Main burner flame proving period tFS2: 0 s
- 30 Air valve can be controlled externally
- 31 Air valve can be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 35 UVS check (1 x in 24 hours)
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for single-electrode operation
- Time between two start-ups: 15 s
Burner control unit, series 400
- Version for pilot and main burner
- 1st safety time on start-up (burner/pilot burner) tSA1: 5 s
- 2nd safety time on start-up (main burner) tSA2: 3 s
- Safety time in operation tSB: 1 s
- Air valve control
- Mains voltage: 230 V AC, 50/60 Hz
- Ignition transformer TZI 7,5-12/100
- Front film in English with additional stickers in D, F, I, NL, E
- High temperature operation: with intermittent operation with UVS
- 3 start-up attempts, pilot burner
- 1 start-up attempt, main burner
- PROFIBUS-DP interface
- Integrated Variosub PROFIBUS-DP chassis socket, 9-pin
- 04 Burner/pilot burner switch-off threshold: 1 mikro A
- 05 Main burner switch-off threshold: 7 mikro A
- 12 Fault lock-out after pilot burner failure in operation
- 13 Fault lock-out after main burner failure in operation
- 15 Flame simulation check in start-up/standby position
- 16 Permanent pilot burner
- 20 Minimum combustion time tB: as safety time on start-up tSA(2)
- 21 Minimum burner pause time tBP: 0 s
- 23 Burener/pilot burner flame proving period tFS1: 3 s
- 25 Main burner flame proving period tFS2: 3 s
- 30 Air valve can be controlled externally
- 31 Air valve can not be activated externally on start-up
- 32 Air valve in the event of malfunction: can be controlled
- 34 Combustion time during manual mode limited to 5 min.
- Pre-wired for single-electrode operation
- Time between two start-ups: 15 s