Biztonsági rendszer vezérlőegység FCU 500
Vezérlőegység központi biztonsági funkciók ellenőrzésére és felügyeletére ipari kemencék több égős rendszerén. A készülék többek között ellenőrzi a gáz minimum, gáz maximum, levegő minimum nyomáskapcsolókat, végrehajtja az előszellőztetés, tömörségvizsgálatot, biztosítja a kemencét túlfűtés ellen és a biztonsági feltételek megléte esetén engedélyezi az égők indítását.
EK típusvizsgálattal és tanusítással. Tanusítással SIL 3 és PL e rendszerekhez.
FCU 500: központi kemence vezérléshez
FCU 505: zóna vezérléshez
Működtető feszültség: 120 V AC vagy 230 V AC
Elérhető opciók:
- Levegő pillangószelep vagy frekvenciaváltó vezérlés
- Tömörségvizsgálat külső nyomáskapcsolóval
- Hőmérsékletfelügyelet túlfűtés elleni biztosításhoz vagy magas hőmérsékletű üzemeléshez
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- Modulating capacity control with interface for actuator IC
- With temperature monitoring
- Screw terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 22 Type K double thermocouple NiCr-Ni
- 23 Temperature difference limit: 50 °C
- 24 Lower limit for high temperature operation: 750 °C
- 25 Upper limit of the furnace or flue gas temperature: 350 °C
- 26 Temperature hysteresis: 50 °C
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Fault lock-out, if the fan does not operate
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 6000 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 72 Function of terminal 67: if there is no ready signal from BCU, a fault lock-out will be performed
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- No capacity control
- With temperature monitoring
- Screw terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 22 Type K double thermocouple NiCr-Ni
- 23 Temperature difference limit: 50 °C
- 24 Lower limit for high temperature operation: 750 °C
- 25 Upper limit of the furnace or flue gas temperature: 350 °C
- 26 Temperature hysteresis: 50 °C
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Fault lock-out, if the fan does not operate
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 6000 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 72 Function of terminal 67: if there is no ready signal from BCU, a fault lock-out will be performed
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- Without integrated tightness control or POC
- Modulating capacity control with interface for actuator IC
- With temperature monitoring
- Screw terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 22 Type K double thermocouple NiCr-Ni
- 23 Temperature difference limit: 50 °C
- 24 Lower limit for high temperature operation: 750 °C
- 25 Upper limit of the furnace or flue gas temperature: 350 °C
- 26 Temperature hysteresis: 50 °C
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Fault lock-out, if the fan does not operate
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 6000 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 72 Function of terminal 67: if there is no ready signal from BCU, a fault lock-out will be performed
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- Without integrated tightness control or POC
- No capacity control
- With temperature monitoring
- Screw terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 22 Type K double thermocouple NiCr-Ni
- 23 Temperature difference limit: 50 °C
- 24 Lower limit for high temperature operation: 750 °C
- 25 Upper limit of the furnace or flue gas temperature: 350 °C
- 26 Temperature hysteresis: 50 °C
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Fault lock-out, if the fan does not operate
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 6000 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 72 Function of terminal 67: if there is no ready signal from BCU, a fault lock-out will be performed
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- Modulating capacity control with interface for actuator IC
- Without temperature monitoring
- Spring force terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Fault lock-out, if the fan does not operate
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 6000 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up and after furnace shut-down
- 53 Tightness control test volume: Vp
- 56 Test period Vp: 10 s
- 59 Opening time V1 (tL1): 2 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 72 Function of terminal 67: if there is no ready signal from BCU, a fault lock-out will be performed
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- Modulating capacity control with interface for actuator IC
- Without temperature monitoring
- Spring force terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Fault lock-out, if the fan does not operate
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 0 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 40 Air control with IC 20
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable on
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up
- 53 Tightness control test volume: Vp
- 56 Test period Vp: 10 s
- 59 Opening time V1 (tL1): 2 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 69 Function of terminal 51: AND gating with the input at terminal 48 (purging air pressure switch)
- 72 Function of terminal 67: if there is no ready signal from BCU, a fault lock-out will be performed
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- Modulating capacity control with interface for actuator IC
- Without temperature monitoring
- Spring force terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 31 Safety shut-down, if the fan does not operate
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 1000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 0 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 40 Air control with IC 40
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable on
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up
- 53 Tightness control test volume: Vp
- 56 Test period Vp: 10 s
- 59 Opening time V1 (tL1): 2 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 69 Function of terminal 51: RBW High position feedback
- 72 Function of terminal 67: if there is no ready signal from BCU, a safety shut-down will be performed
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- Modulating capacity control with interface for actuator IC
- Without temperature monitoring
- Spring force terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Fault lock-out, if the fan does not operate
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 6000 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 40 Air control with IC 20
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable on
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up
- 53 Tightness control test volume: Vp
- 56 Test period Vp: 10 s
- 59 Opening time V1 (tL1): 2 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 72 Function of terminal 67: if there is no ready signal from BCU, a fault lock-out will be performed
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- Modulating capacity control with interface for actuator IC
- Without temperature monitoring
- Spring force terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Fault lock-out, if the fan does not operate
- 32 Controlled air flow monitoring off, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 0 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up
- 53 Tightness control test volume: Vp, venting via V3
- 56 Test period Vp: 600 s
- 59 Opening time V1 (tL1): 2 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 73 Function of terminal 68: safety input relay feedback
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- Modulating capacity control with interface for actuator IC
- Without temperature monitoring
- Spring force terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Fault lock-out, if the fan does not operate
- 32 Controlled air flow monitoring off, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 0 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up
- 53 Tightness control test volume: Vp, venting via V3
- 56 Test period Vp: 600 s
- 59 Opening time V1 (tL1): 2 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- Modulating capacity control with interface for actuator IC
- Without temperature monitoring
- Spring force terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Fault lock-out, if the fan does not operate
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 6000 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test after furnace shut-down
- 53 Tightness control test volume: Vp, venting via V3
- 56 Test period Vp: 600 s
- 59 Opening time V1 (tL1): 2 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 72 Function of terminal 67: if there is no ready signal from BCU, a fault lock-out will be performed
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- Modulating capacity control with interface for actuator IC
- Without temperature monitoring
- Screw terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Fault lock-out, if the fan does not operate
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 6000 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up and after furnace shut-down
- 53 Tightness control test volume: Vp
- 56 Test period Vp: 10 s
- 59 Opening time V1 (tL1): 2 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 72 Function of terminal 67: if there is no ready signal from BCU, a fault lock-out will be performed
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- Modulating capacity control with interface for actuator IC
- Without temperature monitoring
- Screw terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Fault lock-out, if the fan does not operate
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 6000 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 72 Function of terminal 67: if there is no ready signal from BCU, a fault lock-out will be performed
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- Modulating capacity control with interface for actuator IC
- Without temperature monitoring
- Screw terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Fault lock-out, if the fan does not operate
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 6000 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up
- 53 Tightness control test volume: Vp
- 56 Test period Vp: 10 s
- 59 Opening time V1 (tL1): 2 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 72 Function of terminal 67: if there is no ready signal from BCU, a fault lock-out will be performed
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- Modulating capacity control with interface for actuator IC
- Without temperature monitoring
- Screw terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with safety shut-down
- 12 High gas pressure protection with safety shut-down
- 13 Low-pressure cut-off with safety shut-down
- 15 Air monitoring with safety shut-down
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 5 s
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 60 s
- 35 Pre-purge air monitoring with safety shut-down
- 37 Post-purge time tPN: 0 s
- 38 post-purge: The controller enable signal for the actuator (if there is one) is issued without air monitoring
- 40 Air control with IC 20
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable on
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up
- 53 Tightness control test volume: Vp, venting via V3
- 56 Test period Vp: 100 s
- 59 Opening time V1 (tL1): 3 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- Modulating capacity control with interface for actuator IC
- Without temperature monitoring
- Screw terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with safety shut-down
- 12 High gas pressure protection with safety shut-down
- 13 Low-pressure cut-off with safety shut-down
- 15 Air monitoring with safety shut-down
- 19 Safety time during operation: 1 s
- 29 Fan is switched on in the event of fault
- 30 Fan run-up time tGV: 5 s
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 60 s
- 35 Pre-purge air monitoring with safety shut-down
- 37 Post-purge time tPN: 0 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 40 Air control with IC 20
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable on
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up
- 53 Tightness control test volume: Vp, venting via V3
- 56 Test period Vp: 100 s
- 59 Opening time V1 (tL1): 3 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- Modulating capacity control with interface for actuator IC
- Without temperature monitoring
- Screw terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Fault lock-out, if the fan does not operate
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 6000 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up
- 53 Tightness control test volume: Vp, venting via V3
- 56 Test period Vp: 100 s
- 59 Opening time V1 (tL1): 3 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 72 Function of terminal 67: if there is no ready signal from BCU, a fault lock-out will be performed
- 73 Function of terminal 68: safety input relay feedback
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- Modulating capacity control with interface for actuator IC
- Without temperature monitoring
- Screw terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with safety shut-down
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Fault lock-out, if the fan does not operate
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 0 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 40 Air control with IC 20
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable on
- 47 Controller enable (Timeout): 0 min.
- 51 Tightness control test before furnace start-up
- 53 Tightness control test volume: Vp
- 56 Test period Vp: 10 s
- 59 Opening time V1 (tL1): 2 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 72 Function of terminal 67: if there is no ready signal from BCU, a fault lock-out will be performed
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- Modulating capacity control with interface for actuator IC
- Without temperature monitoring
- Screw terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 0 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up
- 53 Tightness control test volume: Vp, venting via V3
- 56 Test period Vp: 3600 s
- 59 Opening time V1 (tL1): 3 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 69 Function of terminal 51: AND gating with the input at terminal 48 (purging air pressure switch)
- 73 Function of terminal 68: safety input relay feedback
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- Modulating capacity control with interface for actuator IC
- Without temperature monitoring
- Screw terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Fault lock-out, if the fan does not operate
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 6000 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test after furnace shut-down
- 53 Tightness control test volume: Vp, venting via V3
- 56 Test period Vp: 600 s
- 59 Opening time V1 (tL1): 2 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 72 Function of terminal 67: if there is no ready signal from BCU, a fault lock-out will be performed
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- Modulating capacity control with interface for actuator IC
- Without temperature monitoring
- Screw terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Fault lock-out, if the fan does not operate
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 6000 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- Modulating capacity control with interface for actuator IC
- Without temperature monitoring
- No connection terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Fault lock-out, if the fan does not operate
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 6000 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up and after furnace shut-down
- 53 Tightness control test volume: Vp
- 56 Test period Vp: 10 s
- 59 Opening time V1 (tL1): 2 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 72 Function of terminal 67: if there is no ready signal from BCU, a fault lock-out will be performed
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- No capacity control
- Without temperature monitoring
- Spring force terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Fault lock-out, if the fan does not operate
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 6000 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up and after furnace shut-down
- 53 Tightness control test volume: Vp
- 56 Test period Vp: 10 s
- 59 Opening time V1 (tL1): 2 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 72 Function of terminal 67: if there is no ready signal from BCU, a fault lock-out will be performed
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- No capacity control
- Without temperature monitoring
- Spring force terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 0 s
- 37 Post-purge time tPN: 0 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up
- 53 Tightness control test volume: Vp
- 56 Test period Vp: 10 s
- 59 Opening time V1 (tL1): 2 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 72 Function of terminal 67: if there is no ready signal from BCU, a fault lock-out will be performed
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- No capacity control
- Without temperature monitoring
- Spring force terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with safety shut-down
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 10 s
- 32 Fault lock-out, if the fan does not operate
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 0 s
- 37 Post-purge time tPN: 10 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up and after furnace shut-down
- 53 Tightness control test volume: Vp, venting via V3
- 56 Test period Vp: 10 s
- 59 Opening time V1 (tL1): 2 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 72 Function of terminal 67: if there is no ready signal from BCU, a fault lock-out will be performed
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- No capacity control
- Without temperature monitoring
- Spring force terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Fault lock-out, if the fan does not operate
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 6000 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up and after furnace shut-down
- 53 Tightness control test volume: Vp
- 56 Test period Vp: 600 s
- 59 Opening time V1 (tL1): 3 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 72 Function of terminal 67: if there is no ready signal from BCU, a fault lock-out will be performed
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- No capacity control
- Without temperature monitoring
- Spring force terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Fault lock-out, if the fan does not operate
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 6000 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up
- 53 Tightness control test volume: Vp, venting via V3
- 56 Test period Vp: 100 s
- 59 Opening time V1 (tL1): 3 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- No capacity control
- Without temperature monitoring
- Spring force terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 0 s
- 37 Post-purge time tPN: 0 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up
- 53 Tightness control test volume: Vp, venting via V3
- 56 Test period Vp: 230 s
- 59 Opening time V1 (tL1): 2 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- No capacity control
- Without temperature monitoring
- Spring force terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 0 s
- 37 Post-purge time tPN: 0 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up
- 53 Tightness control test volume: Vp, venting via V3
- 56 Test period Vp: 60 s
- 59 Opening time V1 (tL1): 2 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 72 Function of terminal 67: if there is no ready signal from BCU, a safety shut-down will be performed
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- No capacity control
- Without temperature monitoring
- Spring force terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Fault lock-out, if the fan does not operate
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 6000 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up
- 53 Tightness control test volume: Vp, venting via V3
- 56 Test period Vp: 600 s
- 59 Opening time V1 (tL1): 2 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 73 Function of terminal 68: safety input relay feedback
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- No capacity control
- Without temperature monitoring
- Spring force terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 0 s
- 37 Post-purge time tPN: 0 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up
- 53 Tightness control test volume: Vp
- 56 Test period Vp: 10 s
- 59 Opening time V1 (tL1): 2 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 69 Function of terminal 51 :AND gating with the input at terminal 47 (air pressure switch)
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- No capacity control
- Without temperature monitoring
- Spring force terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Fault lock-out, if the fan does not operate
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 6000 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up
- 53 Tightness control test volume: Vp
- 56 Test period Vp: 10 s
- 59 Opening time V1 (tL1): 2 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 69 Function of terminal 51: AND gating with the input at terminal 46 (emergency stop)
- 72 Function of terminal 67: if there is no ready signal from BCU, a fault lock-out will be performed
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- No capacity control
- Without temperature monitoring
- Spring force terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Controlled air flow monitoring off, butterfly valve open
- 34 Pre-purge time tPV: 300 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 0 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up
- 53 Tightness control test volume: Vp, venting via V3
- 56 Test period Vp: 100 s
- 59 Opening time V1 (tL1): 10 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 69 Function of terminal 51: AND gating with the input at terminal 46 (emergency stop)
- 72 Function of terminal 67: if there is no ready signal from BCU, a safety shut-down will be performed
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- No capacity control
- Without temperature monitoring
- Spring force terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 0 s
- 37 Post-purge time tPN: 0 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up
- 53 Tightness control test volume: Vp, venting via V3
- 56 Test period Vp: 600 s
- 59 Opening time V1 (tL1): 4 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 73 Function of terminal 68: safety input relay feedback
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 120 V AC, 50/60 Hz
- With integrated tightness control or POC
- No capacity control
- Without temperature monitoring
- Screw terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 10 s
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 6000 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up
- 53 Tightness control test volume: Vp, venting via V3
- 56 Test period Vp: 200 s
- 59 Opening time V1 (tL1): 2 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 72 Function of terminal 67: if there is no ready signal from BCU, a fault lock-out will be performed
- 73 Function of terminal 68: safety input relay feedback
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 120 V AC, 50/60 Hz
- With integrated tightness control or POC
- No capacity control
- Without temperature monitoring
- Screw terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with safety shut-down
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 31 Safety shut-down, if the fan does not operate
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 15 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 0 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up
- 53 Tightness control test volume: Vp
- 56 Test period Vp: 10 s
- 59 Opening time V1 (tL1): 2 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- No capacity control
- Without temperature monitoring
- Screw terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 29 Fan is switched on in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Controlled air flow monitoring off, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 6000 s
- 38 post-purge: The actuator (if there is one) moves to the
- open position with air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up
- 53 Tightness control test volume: Vp, venting via V3
- 56 Test period Vp: 3600 s
- 59 Opening time V1 (tL1): 2 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 73 Function of terminal 68: safety input relay feedback
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- No capacity control
- Without temperature monitoring
- Screw terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Fault lock-out, if the fan does not operate
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 6000 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up and after furnace shut-down
- 53 Tightness control test volume: Vp
- 56 Test period Vp: 10 s
- 59 Opening time V1 (tL1): 2 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 72 Function of terminal 67: if there is no ready signal from BCU, a fault lock-out will be performed
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- No capacity control
- Without temperature monitoring
- Screw terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 29 Fan is switched on in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Controlled air flow monitoring off, butterfly valve open
- 34 Pre-purge time tPV: 0 s
- 37 Post-purge time tPN: 6000 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up
- 53 Tightness control test volume: Vp
- 56 Test period Vp: 10 s
- 59 Opening time V1 (tL1): 3 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- No capacity control
- Without temperature monitoring
- Screw terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Fault lock-out, if the fan does not operate
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 0 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up
- 53 Tightness control test volume: Vp
- 56 Test period Vp: 10 s
- 59 Opening time V1 (tL1): 2 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 72 Function of terminal 67: if there is no ready signal from BCU, a fault lock-out will be performed
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- No capacity control
- Without temperature monitoring
- Screw terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Fault lock-out, if the fan does not operate
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 6000 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up
- 53 Tightness control test volume: Vp
- 56 Test period Vp: 10 s
- 59 Opening time V1 (tL1): 2 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 72 Function of terminal 67: if there is no ready signal from BCU, a fault lock-out will be performed
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- No capacity control
- Without temperature monitoring
- Screw terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with safety shut-down
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Controlled air flow monitoring off, butterfly valve open
- 34 Pre-purge time tPV: 600 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 0 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up
- 53 Tightness control test volume: Vp
- 56 Test period Vp: 10 s
- 59 Opening time V1 (tL1): 3 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 69 Function of terminal 51: AND gating with the input at terminal 48 (purging air pressure switch)
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- No capacity control
- Without temperature monitoring
- Screw terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with safety shut-down
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Controlled air flow monitoring off, butterfly valve open
- 34 Pre-purge time tPV: 600 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 0 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up
- 53 Tightness control test volume: Vp
- 56 Test period Vp: 10 s
- 59 Opening time V1 (tL1): 3 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- No capacity control
- Without temperature monitoring
- Screw terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with safety shut-down
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Controlled air flow monitoring off, butterfly valve open
- 34 Pre-purge time tPV: 600 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 0 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up
- 53 Tightness control test volume: Vp
- 56 Test period Vp: 10 s
- 59 Opening time V1 (tL1): 3 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 73 Function of terminal 68: safety input relay feedback
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- No capacity control
- Without temperature monitoring
- Screw terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 600 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 60 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up
- 53 Tightness control test volume: Vp
- 56 Test period Vp: 10 s
- 59 Opening time V1 (tL1): 3 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- No capacity control
- Without temperature monitoring
- Screw terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Fault lock-out, if the fan does not operate
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 6000 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 72 Function of terminal 67: if there is no ready signal from BCU, a fault lock-out will be performed
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- No capacity control
- Without temperature monitoring
- Screw terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Fault lock-out, if the fan does not operate
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 0 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up
- 53 Tightness control test volume: Vp1 + Vp2, venting via V3
- 54 Tightness control: pressure reduction Vp2 upon start-up
- 55 Opening time vent valve V3 (tL3): 0 s
- 56 Test period Vp: 10 s
- 57 Test period Vp1 + Vp2: 10 s
- 59 Opening time V1 (tL1): 2 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 69 Function of terminal 51 :AND gating with the input at terminal 47 (air pressure switch)
- 70 Function of terminal 65: AND gating with the input at terminal 48 (purging air pressure switch)
- 71 Function of terminal 66: AND gating with the input at terminal 49 (low gas pressure switch)
- 73 Function of terminal 68: safety input relay feedback
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- No capacity control
- Without temperature monitoring
- Screw terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Controlled air flow monitoring off, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 0 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up
- 53 Tightness control test volume: Vp, venting via V3
- 56 Test period Vp: 10 s
- 59 Opening time V1 (tL1): 3 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- No capacity control
- Without temperature monitoring
- Screw terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Controlled air flow monitoring off, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 0 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up
- 53 Tightness control test volume: Vp
- 56 Test period Vp: 100 s
- 59 Opening time V1 (tL1): 3 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 73 Function of terminal 68: safety input relay feedback
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- No capacity control
- Without temperature monitoring
- Screw terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 10 s
- 32 Fault lock-out, if the fan does not operate
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 30 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 60 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 62 Minimum pause time tP: 10 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- No capacity control
- Without temperature monitoring
- Screw terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 10 s
- 32 Fault lock-out, if the fan does not operate
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 30 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 60 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up
- 53 Tightness control test volume: Vp1 + Vp2, venting via V3
- 54 Tightness control: pressure reduction Vp2 in standby
- 56 Test period Vp: 10 s
- 57 Test period Vp1 + Vp2: 10 s
- 59 Opening time V1 (tL1): 2 s
- 62 Minimum pause time tP: 10 s
- 63 Switch-on delay time tE: 1 s
- 65 Filling time before start-up: 1 s
- 67 Operating time during manual mode limited to 5 min.
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- No capacity control
- Without temperature monitoring
- Screw terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Fault lock-out, if the fan does not operate
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 6000 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up and after furnace shut-down
- 53 Tightness control test volume: Vp
- 56 Test period Vp: 600 s
- 59 Opening time V1 (tL1): 3 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 72 Function of terminal 67: if there is no ready signal from BCU, a fault lock-out will be performed
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- No capacity control
- Without temperature monitoring
- Screw terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Fault lock-out, if the fan does not operate
- 32 Controlled air flow monitoring off, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 0 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up
- 53 Tightness control test volume: Vp, venting via V3
- 56 Test period Vp: 10 s
- 59 Opening time V1 (tL1): 2 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 73 Function of terminal 68: safety input relay feedback
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- No capacity control
- Without temperature monitoring
- Screw terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 0 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up
- 53 Tightness control test volume: Vp, venting via V3
- 56 Test period Vp: 10 s
- 59 Opening time V1 (tL1): 2 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 73 Function of terminal 68: safety input relay feedback
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- No capacity control
- Without temperature monitoring
- Screw terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Controlled air flow monitoring off, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 0 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up
- 53 Tightness control test volume: Vp, venting via V3
- 56 Test period Vp: 20 s
- 59 Opening time V1 (tL1): 3 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- No capacity control
- Without temperature monitoring
- Screw terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Fault lock-out, if the fan does not operate
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 0 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up
- 53 Tightness control test volume: Vp
- 56 Test period Vp: 100 s
- 59 Opening time V1 (tL1): 2 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 69 Function of terminal 51: AND gating with the input at terminal 48 (purging air pressure switch)
- 72 Function of terminal 67: if there is no ready signal from BCU, a fault lock-out will be performed
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- No capacity control
- Without temperature monitoring
- Screw terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 6000 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up
- 53 Tightness control test volume: Vp
- 56 Test period Vp: 10 s
- 59 Opening time V1 (tL1): 2 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 72 Function of terminal 67: if there is no ready signal from BCU, a fault lock-out will be performed
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- No capacity control
- Without temperature monitoring
- Screw terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Fault lock-out, if the fan does not operate
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 6000 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- No capacity control
- Without temperature monitoring
- Screw terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Fault lock-out, if the fan does not operate
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 6000 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up
- 53 Tightness control test volume: Vp1 + Vp2, venting via V3
- 54 Tightness control: pressure reduction Vp2 upon start-up
- 55 Opening time vent valve V3 (tL3): 20 s
- 56 Test period Vp: 10 s
- 57 Test period Vp1 + Vp2: 360 s
- 59 Opening time V1 (tL1): 2 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 72 Function of terminal 67: if there is no ready signal from BCU, a fault lock-out will be performed
- 77 User-defined Password
Protective system control
- Series 500
- Mains voltage 230 V AC, 50/60 Hz
- With integrated tightness control or POC
- No capacity control
- Without temperature monitoring
- No connection terminals
- EC type-tested and certified, CSA and FM approved, certified for systems up to SIL 3 (compliant with PL e)
- Single packaging
- 10 Emergency stop with fault lock-out
- 12 High gas pressure protection with fault lock-out
- 13 Low-pressure cut-off with fault lock-out
- 15 Air monitoring with fault lock-out
- 19 Safety time during operation: 1 s
- 30 Fan is switched off in the event of fault
- 30 Fan run-up time tGV: 0 s
- 32 Fault lock-out, if the fan does not operate
- 32 Controlled air flow monitoring on, butterfly valve open
- 34 Pre-purge time tPV: 6000 s
- 35 Pre-purge air monitoring with fault lock-out
- 37 Post-purge time tPN: 6000 s
- 38 post-purge: The actuator (if there is one) moves to the open position without air monitoring
- 44 Controller enable delay tRF: 0 s
- 45 Minimum enable time: 0 s
- 46 After operating signal: Controller enable off
- 47 Controller enable (Timeout): 60 min.
- 51 Tightness control test before furnace start-up and after furnace shut-down
- 53 Tightness control test volume: Vp
- 56 Test period Vp: 10 s
- 59 Opening time V1 (tL1): 2 s
- 62 Minimum pause time tP: 0 s
- 63 Switch-on delay time tE: 0 s
- 65 Filling time before start-up: 0 s
- 67 Operating time during manual mode limited to 5 min.
- 72 Function of terminal 67: if there is no ready signal from BCU, a fault lock-out will be performed
- 77 User-defined Password